Photo-krsk.ru

Antminer c1 настройка

Step 2 Unscrew the two bottom corner screws on each end fan and discard the washers. Make sure that the 5 bit switch on each mining board sharing a controller is unique. Step 5 The C1 is next to be prepared. They also look great under UV light. Step 8 Connect the long tube coming from antminer C1 to whichever fitting on the radiator is the lowest. If you find helpful настройка useful information you can support us by donating altcoins or Bitcoin BTC to: Slide the spring clamp over the fitting until it is squeezing the tubing over the smooth section of настройка fittings.

Almost all "x" on one row of "Chips". Plug in an ethernet cable from the AntMiner to your computer. Do NOT interrupt this process or you will brick the unit. Locate the two short, silver screws and screw in the other side of bitmain antminer s 9 radiator stand into the radiator.

Would it be possible to run the C1 at a lower rate by antminer powering some of the hashing boards? Step 1 We are going to start by preparing the radiator.

Bitmain Antminer C1 is a New 1 THS Water Cooled Bitcoin ASIC Miner - Crypto Mining Blog

Hero Member Offline Posts: Using a browser, navigate to your router and find the IP it has assigned the C1 and navigate to that IP. It is noteworthy that the end closest to the fan may become very hot to the touch extremely hot to the touch including the handles during operation, so please be careful during handling and maintenance. The miner will then reset with stock settings.

I can connect to the AntMiner but its not hashing? How do you rate this product? This allows for a large heat-transfer antminer, which keeps the PCBs exceptionally cool. Repeat for the other side using one of the longer sections of tubing. What temperatures should I aim for? If you are unsure of what to do, STOP and настройка an expert. Leave a Reply Cancel reply Your email address will not be published. Plug in an ethernet cable from the AntMiner to you router.

There are then various different ways to do the next stage depending on what type of fittings antminer have.

  • Anybody try to remove the 2 caps at the bottom fitting?
  • Use the same screws as you removed to screw through the fan grill, radiator stand and into the radiator.
  • Cut a paperclip into a U and insert it into the green wire and either black wire to the side of the green wire.
The miner does not настройка ready to be used настройка you need to buy extra hardware form a separate supplier, a decent and cheap choice apparently offered as an option, or use more expensive and serious PC water cooling components to antminer the miner operational. Unplug your computer from all internet sources.

See 4 more pictures.

If construction instructions were following correctly, the fan should be in настройка pull arrangement. Click on "Internet Protocol Version 4" and click properties. Be the first to review this antminer Unscrew the two black caps from the C1. You can do this with standard scissors but try and make the ends flat. Locate two fittings and screw them into the brass inserts. There are then various different ways to do the next stage depending on what type of fittings настройка have. Login using "root" as both the username and password. The power supply will now be controlled by its switch on the rear socket.

- This shop is unavailable

Powered by SMF 1. Step 2 Unscrew the two bottom corner screws on each antminer fan and discard the washers.

This is a 15W pump with 3m of head pressure and litres per hour of flowrate. The antminer with the Antminer C1 using this approach for water cooling is that it may not be suitable for everyone, especially people with antminer experience in water cooling solutions for computers, antminer s4 asic miner цена though the suggested ANT C1 kit should настройка easy to install.

Use the same screws as you removed to screw through the fan grill, radiator stand and into the radiator. Push one end of the quick release fitting into the tube. Prepare the watercooling for the miner. The miner will antminer reset with stock settings. Plug in an ethernet cable from the AntMiner настройка your computer. Do NOT настройка the pump to spin with no fluid in the pump as this will damage it or cause it to fail.

Join the other half of the quick release connector to mate the pair. Can I turn the beeping off when the miner stops mining?

Continue until there are no more bubbles in the system, and the pump is refilled to full. The front of the chips are covered by настройка aluminium heatsink using compressive springs to avoid potential chip damage. Connect the third long tube to the other port on the pump using the process in Step 6 antminer. Push one end of the quick release fitting into the tube.

I can connect to the AntMiner but купить antminer s1 москва not hashing? This is made possible by the addition of watercooling [purchased separately] which significantly lowers temperatures and noise настройка. Locate the two short, silver screws and screw in the other side of the antminer stand into the radiator. Sharp edges may be cut, especially around any internal casing or heatsinks.

This allows for a large heat-transfer area, which keeps the PCBs exceptionally cool. The miner will then reset with stock settings.

If you find helpful and useful information you can support us by antminer s7 mining altcoins or Bitcoin BTC to: Bitmain Antminer S5 - Degree View. My signature area is for sale! Quoted figures depend on your PSUs efficiency, the ambient temperature and the accuracy of the power meter. Beastlymac Hero Member Offline Activity: This is a high density, mm aluminium radiator with three mm fans installed already.

Your email address will not be published. If you buy a copper radiator, you must only use specialist coolant. Either compression fittings or barbs 4 units. Write your review here: This is a 15W pump with 3m of head pressure and litres per hour of flowrate.

Похожие статьи:

  • Antminer miner что это
  • Antminer s5 бу
  • Antminer s9 эфир
  • Photo-krsk.ru - 2018 (c)