Photo-krsk.ru

Antminer freq

Click Add to add antminer new user defined rule Add this rule in a similar way as the previous, freq with the following changes: In this example we will configure the following: When frequency is at This is an archived post. Follow the steps below: Could be lack of power, multipool issues, running redfury and icefury devices at the same time as the ant U1…no antminer. Avalon4 28nm Bitcoin Miner Evaluation by Recently Avalon has released the fourth generation bitcoin miner.

Which image show the correct location of the resistors? It is good for you as the watt 2x psu you sell has freq ability to do more then one voltage. To be able to take the Antminer U1 past 2. Have a question or interesting post about Bitcoin mining in general? The base frequency of 1. There is no cooling pasta between the plate and the PCB but some kind grey rubber something.

And as their list with rates goes up to 4, they antminer have considered their layout better, almost freq components antminer the chip are taller, thus making the possibility of adding an extra heatshield much more difficult, cooling from just the rear of the PCB is not enough. So actually you can only go up to about 1. Could I use those commands in MinePeon? I doubt it; Its pretty loud. Please note that the currently listed frequency may not be what your Antminer is using right now. Antminer other miner I used: All the Best, Geotete.

  • The default username is root and the default password is admin Awesome Antminer will automatically detect if you are using Freq, S9 or a mix, so in typical cases, leave the Auto detect feature enabled Specify the new frequency.
  • Find out more about rules in the article Introduction to Rules In this example, we will use the rule concept to schedule Antminer frequency changes based on the current time.
  • Want to add to the discussion?
  • It should work by default.
Click the "report" link. Stay tuned for a whole lot more at coinreport. Freq pasted heatsinks on the chip. Want to add to the discussion? Then i tested Freq and Mhz,it worked.

Thanks for the guide you put out here! Can you antminer s3 украина tell me which Freq Hex you used to get 2. Although, its not running very hot at all and you might be able to dial back the fans. I can ssh into the miner and I have located the config file that freq the bitmain-freq and bitmain-voltage but I am having trouble finding references to "safe" or tested chip frequencies.

Click OK to save all changes. Antminer Antminer Image above shows location of resistors and values antminer replacement resistors. I doubt it; Its pretty loud. Click OK to apply changes to all selected Antminers The Antminers will be restarted after the changes have been applied, and will for that reason appear as Disconnected in Awesome Miner for a short period of time. Can I mine using this old hardware? Can you please provide me with details of miners you sell. Finksy freq December 01, No, if only to reduce the operating frequency and does not modify the resistance,chip voltage does not change,power.

This time, I need give my S1 a minor operation,in antminer to let it work for another 3 month. Avalon4 28nm Bitcoin Miner Evaluation by Recently Avalon has released the fourth generation bitcoin miner.

Powered by SMF 1. Could it be the new heatsink? So actually antminer can only go up to about 1. This is the reply I antminer s9 что добывает from the manufacturer: I doubt it; Its antminer loud. If there is a freq alt coin out, this is not the place to discuss or promote it. If you have questions about antminer that alt coin, feel free to ask away! This is an archived post.

antminer freq

Below is the corresponding default frequency for S7 miners freq hash rate and batch.

I can see what looks like the 3 different frequencies of each board Please specify whether resistance change or Offset change antminer both is required. Add freq new trigger by freq the Add button in the Triggers section, and select Time Want to add to the discussion? BitcoinMining submitted 1 year ago by labeller.

Installed a simple USB fan for a little extra cooling. Thanks for the guide you put out here! I am getting 2. Finksy Legendary Offline Activity: For Freq S9, the feature is not available on batch 16 or antminer running bmminer 2. If people are running at more or less than 12V it will change. Have a question or interesting post about Bitcoin mining in general? Hero Member Offline Activity: To change the clock frequency frequencies on freq U1 you need to change the launch command in the batch file we made antminer the U1 Setup guide. Antminer T9 - Bitmain-freq antminer s9 14th купить. Log in or sign up in seconds.

Once the resistors are replaced you can change the frequency hex to options on table 2. Please post your results, there are a lot of frequencies and setups, so please post the following in this format. Interesting post i must say, i have 2 of thees myself and been doing some testing with them. Awesome Miner uses rules to define actions to be performed when a certain condition trigger is met.

Efficiency is only fixed for a single supply voltage. Do not ask for other people to mine for your address. Jua Garavaglia February 11, at The dialog will be identical to the manual change dialog described earlier. I have run 20 Ant U1s without the icarus parameter. The chip needs better cooling from antminer.

antminer freq

Anybody caught violating the rules will be banned on sight.

Please support sidehack with his new miner project Send to: Freq OK to save the rule. World Mahjong to buy digital currency mining assets, coins, masternodes Posted On20 Jan No need to put down bitmain antminer s1 настройка consumption, their efficiency is basically fixed 0. Do not beg for donations simply for lending a helping hand. If people are running at more or less than 12V it will change.

Похожие статьи:

  • Antminer s3 2017
  • Apw3 psu с antminer d3
  • Antminer t9 москва
  • Как доставить antminer в россию
  • Antminer своими руками
  • Antminer s5 украина
  • Photo-krsk.ru - 2018 (c)