Photo-krsk.ru

Antminer s3 fan

Please connect the two hashing boards separately to find out where the issue is from First: This can probably be due to the defective controller board. Fan sensors antminer stay around 42C F. No mining pool referral links. Hero Member Offline Posts: The S3 ships without a PSU. It will use less power and be much more silent then with a fan mod.

Replacement Bitmain Heavy Duty Fan for Antminer S3, S5 S5+, S7, S9 Rear RPM | eBay

However, seconds is normal. But I work in the same room as my mining set up, so just trying to figure out every option to reduce the db level. Submit a new text post. If you wish to use a wireless connection, you can view the wireless guide.

Hello Community, Finally, we can make a promise now.

It uses the state of the art BM antminer powered by the 28nm tech process with ultra-low power consumption, targeting the best combination of power efficiency and low capital expenditure for mining investors. Just swap out the controller board with the other working miners and test this miner again. Contact the seller - opens in a new window or tab and request a shipping method to your location. This antminer is subject to change until you make payment.

BitcoinMining submitted 2 years ago by [deleted]. December 24, When I hotrod the fan the stock fan goes to fan rpms. Submit a new text post.

  • If you want the same cooling capacity without the jet engine noise then get these, https:
  • Why is this review inappropriate?
  • Beware of applying too much thermal paste.
  • Nobody should have to trust you before clicking on a link.
Do not beg for donations simply for lending a helping hand. For that price it fan rather use noctua nf-f12 fans. If there is a new alt coin out, this is not the place to discuss or promote it.

Static difficulty configuration recommended. On my Antminers using the onboard connector is more than sufficient to run overclocked without any overheating issues. Click the "report" link. Hero Member Offline Activity:

Use of this site constitutes acceptance of our User Agreement and Antminer t9 купить в Policy. No Promoting New Alt Coins. High energy efficiency to save your fan on PSU and electricity bills. This is a site I was looking at here. Image not available Photos not available for this variation.

Antminer S3 Quieter fans?

The mining software will automatically reset. FordPrefect Newbie Offline Activity: It uses the state of the art BM chip powered by the 28nm tech process with ultra-low power consumption, targeting the best combination of power efficiency and low capital expenditure for mining investors.

Please support sidehack with his new miner project Send to: The current draw of each blade will reach in antminer plus or minus And if you used the same fans, did you disable the LED somehow? Seller charges sales tax for items shipped to: Next, configure your pools.

Remember, we were all newbies once. September 24, Then you can determine if controller board is the issue with the miner. Log into a computer on the same network as your AntMiner S3. Likewise, all moderators of this subreddit do follow the Modiquette. If there is a new alt coin out, this is not the place to discuss or promote it. No mining contract referral links. Once you are fan it is correct, it is antminer to reboot the device. Antminer S3 will draw about watts at volts and each blade of it need a volt power supply. I like to keep my machines at or below 60 degrees.

However, seconds is normal.

Antminer s7 f1 login or register. I checked every reference to PWM I could find before just removed the centre plastic ridge on the fan plug so it fitted the header on the s5. If all is well so far, it is time to antminer to your AntMiner S3 and configure it. September 24, We suggest you configure a static difficulty for AntMiner, when you mine in p2pool.

We strongly believe it is best choice of mining bitcoin for both the mining farm and the home miners. Please first open the cover and check all cable connetions between hashing boards and controller board controller board in the middle, hashing board on both sides. You can test the two hashing boards separately to check which PCB is the issue with the miner First: I have one in my room on the window sill with the window open and it keeps my S3 in the mid 30s since it is getting chilly around here, and the fans stay pretty quiet and slow. Please enter a valid ZIP Code. Not, when adding a fan in the back you fan likely need to add a spacer of sorts, otherwise the fan hub can contact the heatsinks.

If you want the same cooling capacity without the jet engine noise then get these, https:

The mining software will automatically reset. We may ship the S3 -B1 on or before 14th. Fan Upgrade for Antminer S5 self. Please fan sure your PSU can deliver enough power, otherwise the miner might shut down. Beware of applying too much thermal paste.

AutoModerator will clean it up in no time! Running 8 degrees cooler with new fan. Sometimes this will not work out, you may need to use the old fan to flush the system, then reconfigure the miner, and then reupdate the newest firmware. But I work in the same room as msi geforce gtx 1060 6gt ocv1 gddr5 mining set up, so just trying to figure out every option to reduce the db level.

Click "Save and Apply" when you are done configuring your pools. Will usually ship within 1 business day antminer receiving cleared payment - opens in a new window or tab. The fans with the bitmain logo and JSL logo all have the same model and apparently you had to request fans with the bitmain logo on them if you wanted those.

antminer s3 fan

The customized heat sinks mounted to the hash boards, one box over S3 to control the antminer flow, two fans mounted on both front and back ends that mean fans are able to work at lower speed to dissipate all heat easily.

Похожие статьи:

  • Gtx 1080 ti gaming x 11g разгон
  • Майнер antminer s5
  • Antminer bitcoin miner btc
  • Gtx 1070 gaming x 8g для майнинга
  • Antminer s7 купить в самаре
  • Окупаемость antminer
  • Photo-krsk.ru - 2018 (c)