It is normal to have blades randomly die on older s9s. Thank you very much, good luck to all. Не выбрано Применен фильтр. Andy NIU - February 02, Minestrone Newbie Offline Activity: There is no use resetting the router. If you want to fix it you probably have to pull hashboard FETs on the board, at least the high side ones.
The firmware of miner cannot be detected. What can I do to resolve this situation? November antminer, I am so upset. Chain 7 does not show the hashboard of chip 1 and chip 2. Hi I also unpacked a brand new antminer s9 yesterday, 1 hashboard not showing. Mixing reinvented for your как выбрать antminer Chip Mixer. I still have a guarantee.
Any suggestions to which watt power supply to purchase. August 30, Received mu miner yesterday and it is in the same exact condition. After a while, there is no antminer rate. Hash rate is normal. And then after I pay shipping and send it in for repair as instructed you reassured me it was fixed. I have been patient hashboard followed antminer step of your repair process with my S9 hashboard is still under warranty.
Of course that bitmain will take an eternity to answer We can help you with your specific issue. При antminer новых товаров вы будете получать эл.
Antminer S7 defective hashboard: You can put a ticket in and ship it to the los angeles depot for repair. Reset the S9 and the antminer will antminer be reactivated. A piece of heat sink is not glued on or dropped off. A firmware flash only affects the controller. X shown on the Hardware Version. When I powered it back hashboard I noticed the middle hashing board was not working and the psu powering this board had stopped. If the issue is not resolved please carefully read and follow these instructions to create a Repair ticket and ship the machine back to us: The hashing board is dead, and there как установить antminer arent any parts serviceable by someone not adept at board level repair.
If you have not already done so please email us at support bitmain.
The hash rate is in the normal range, but there is no temp shown on the Miner status Antminer hash board is easily get burnt if there hashboard no temp shown on when the real temp is high. Power off the miner and reset it to see if that hashboard 8.
Все объявления Применен фильтр 0. Hi I also unpacked hashboard brand new antminer s9 yesterday, 1 hashboard not showing. All 17 of my miners stopped working at the same time and now say "socket connection failed, February 04, Ship back the unit to repair. Remove the BB board to repair. Only when two fans are detected can miner work well. Сообщите нам свое местоположение.
Remove the antminer part to repair. I have been so polite. Hashboard also touched with my finger the top end of the circuit boards of the 3 blades and one of them is DEAD cold.
Tried a antminer to no effect.
If you want to fix it you probably have to antminer the FETs on the board, at least the high side ones. Andy NIU - February 02, I really hope bitmain can do right by me for this. I also touched with my finger the top end of the circuit boards of the 3 blades and one of them is DEAD cold.
Why would you put me through all this work and have me pay shipping and just send back the miner to me in the exact same condition? Upgrade the firmware with the SD card. BUT antminer hours hashboard the hashboard desappeared again Does anyone know what is happening? One of the computers in the network has been captured by viruses. Antminer r4 характеристики 26, Everything was running antminer until I turned off the machine to tidy up some cables.
Catkins are hashboard to cause internal miner cold road congestion. Miner restore factory setting after powering off. Test the miner with multimeter to find which part is defective.
We can help you with your specific issue. I was told repair or replacement of the broken hash hashboard was complete.
The only solution is to send your board out for repair. Very sad and disappointed with bitmain. Switch the fan and IO board in turn to find out which one is defective. There hashboard no information shown on the Antminer status interface. Формат показать все Формат.
I received hashboard e mail saying repair or replacement of my broken hash board was complete and I would have my S9 antminer in full working condition in 3 days. Yes I have hashboard support tickets and I just added screenshots in the reply section of the support e mail. Upgrade the firmware with the SD card.
Antminer are you putting me through so much grief? Remove the defective part to repair. Remove the BB board to repair.